410 has better corrosion resistance than 416 grade, but lower than 431 grade. Also lower than most of the 400 series ferritic stainless steels, and all of the 300 series austenitic stainless steels.NB. It has optimum corrosion resistance in the hardened and tempered condition and is not therefore recommended for use in the annealed condition. 410 Stainless Steel Annealed - Bergsen MetalProperties of 410 SS Annealed. Similar to other stainless steel alloys, 410 SS annealeds exact material composition determines the properties it exhibits. The composition and physical and mechanical properties of the material are as follows:Composition.
AISI Type 410 is a martensitic stainless steel that provides high strength and hardness with moderate corrosion resistance. A wide range of properties can be developed with different heat treatments, with ultimate tensile strengths ranging from 500 to 1400 MPa. It is magnetic in both the annealed and hardened conditions. 410 Stainless Steel Sheet, Bar & Plate - AMS 5504410 Stainles Steel Physical Properties. The values reported below are typical for Type 410 alloy in the annealed condition. Density:0.276 lb/in 3. Specific Gravity:7.65. Melting Range:2700-2790°F 1482-1532°C. Modulus of Elasticity:29 x 10 6 psi (200 GPa) Coefficient of ASTM A276 410 Round BarSS 410 Round Bar410 Bright The chemical composition of grade Stainless Steel 410 Round Bar is outlined in the following table. Grade C Mn Si P S Cr Ni; 410:min. max.-0.15-1-1-0.04-0.03:11.5 13.5:0.75:A276 410 Round Bar Mechanical and Physical Properties. The mechanical properties of grade A276 410 Round Bar are displayed in the following table.
Alloy 410 is the basic, general purpose martensitic stainless steel that is used for highly stressed parts and provides good corrosion resistance plus high strength and hardness. Alloy 410 contains a minimum of 11.5% chromium which is just sufficient enough to demonstrate corrosion resistance properties in mild atmospheres, steam, and many mild Alloy 410 Martensitic Stainless Steel Plate - Sandmeyer SteelAlloy 410 (UNS S41000) is a 12% chromium martensitic stainless steel plate that can be heat treated to obtain a wide range of mechanical properties. The alloy has good corrosion resistance along with high strength and hardness. In the annealed condition, 410 stainless steel plate is ductile and may be formed. SS 410, Type 410, WNR 1.4006, UNS S41000, AISI 304, Mechanical Properties SS 410, Type 410, WNR 1.4006, UNS S41000, AISI 304, ASTM 410, Grade 410, AFNOR Z 10 C 13 TYPE 410 WNR 1.4006 AISI 410 GRADE 410S UNS S41000 Carbon Manganese Phosphorus Sulfur Silicon Chromium SS 410 AFNOR Z 10 C 13 ASTM 410 TYPE 410 WNR 1.4006 AISI 410 GRADE 410S UNS S41000 UTS, ksi (Mpa) 0.2% YS, ksi (Mpa) Elongation % 2
Grade 410 is the basic martensitic stainless steel; like most non-stainless steels it can be hardened by a "quench-and-temper" heat treatment. It contains a minimum of 11.5 per cent chromium, just sufficient to give corrosion resistance properties. It achieves maximum corrosion resistance when it has been hardened and tempered and then polished.Specification Sheet:Alloy 410 - Sandmeyer SteelAlloy 410 (UNS S41000) is a 12% Chromium Martensitic stainless steel that can be heat treated to obtain a wide range of mechanical properties. The alloy has good corrosion resistance along with high strength and hardness. In the annealed condition 410 is ductile and may be formed. It remains magnetic in both the annealed and heat treated conditions.