[email protected]

ASTM A1008 (CR) vs. ASTM A1011 (HR) - Metal and

Jan 02, 2008 · Mechanical properties of several types of hot-rolled sheet are given in Table 1. Cold-rolled steel sheet forming is produced by the cold reduction of hot-rolled pickled coils, followed by annealing and possibly additional processing, such as temper rolling. Class 1 (E, exposed) should be ordered when a controlled surface finish is required. Aluminium Alloy - General Information - EN Standards for EN Standards for Rolled Aluminium. The old BS1470 standard has been replaced by nine EN standards:EN485-1:Technical conditions for inspection and delivery EN485-2:Mechanical Properties EN485-3:Tolerances for HOT Rolled Material EN485-4:Tolerances for COLD Rolled material EN515:Temper Designations EN573-1:Numerical alloy designation system

Cold rolled ::ArcelorMittal USA

Cold-rolled sheet steel is produced from hot-rolled sheet with additional processing steps such as pickling, cold reduction, annealing and temper rolling. Cold-rolled steel is a product that has been cold reduced, as opposed to hot-rolled, in order to impart specific mechanical properties, surface finish, gauge tolerance and strip shape. Cold rolled stainless steel coil, strip and sheet OutokumpuCold rolled coil, strip and sheet. A wide selection for a variety of use; our cold rolled coil, strip and sheet products are available in both heat- and corrosion resistant forms. In addition, their standard and special surface finishes provide a unique level of customization. Comparison table - RMIGNorm acc. Din/EN:St 37-2:Fe 360 B:S235JR:1.0038:10025/10029: 10025/10029 HR, Hot Rolled coils and sheets, pickled and oiled Old Old Actual Grade no. Norm acc. Din/EN:St W 22:Fe P11:DD11: QStE 380 TM:FeE 355 TM:S355MC:1.0976:10149/10051:QStE 460 TM:FeE 420 TM:S420MC:1.0980:10149/10051 CR, Cold Rolled coils and sheets Old

EN 10130 DC01 Steel 1.0330+ZE Material Data Sheet

DIN EN 10130 DC01 Steel (1.0330 Material) Data Sheet DC01 steel (1.0330 material) is a European standard cold-rolled quality low-carbon steel flat product for cold forming. In BS and DIN EN 10130 standard, it contains 5 other steel grades:DC03 (1.0347), DC04 (1.0338), DC05 (1.0312), DC06 ( 1.0873) and DC07 (1.0898), the surface quality is divided into 2 types:DC01-A and DC01-B. Equivalent Grades, Alloy Steel,Mild Steel,Stainless steel USA Japan Germany U. K. France Italy Spain Sweden China; AISI/SAE JIS W.-nr. DIN BS EN AFNOR UNI UNE SS GB; A570.36:STKM 12A STKM 12C:1.0038:RSt.37-2:4360 40 C E 24-2 Ne Hot Rolled Steel & Cold Rolled Steel - Difference & May 22, 2019 · Thus, the yield strength of cold rolled steel is higher than that of hot rolled steel. As an example, a hot rolled steel product may have a yield strength of 235 MPa. In comparison, a cold rolled steel product with the same chemical composition has a yield strength of 365 MPa. The main advantages of cold working are:Accurate finished dimensions.

S235JR(1.0038)/ S235J0(1.0114)/S235J2 carbon structural plate

S235JR(1.0038)/ S235J0(1.0114)/S235J2 carbon structural plate. Thickness :Width:according to your requests. Standard:ASTM, EN, GB:Coil Weight:3-10 ton:Length:As your require:Usage:Building, industrial and other fields:Delivery Time:About 15 working days if the quanlity below 500 ton:Packing:According to you requirements Stainless Steel EN Standards for Cold Rolled*Note:Special finishes indicate hot rolled (1) and cold rolled (2) sheets, e.g.:Ground polished hot rolled sheets = 1G / Ground polished cold rolled sheets = 2G For more information on stainless steel finishes please refer to the Aalco technical datasheet on this subject. Steel Standards - ASTM InternationalStandard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, Produced by Twin-Roll Casting Process:A1088 - 13(2019) Standard Specification for Steel, Sheet, Cold-Rolled, Complex Phase (CP), Dual Phase (DP) and Transformation Induced Plasticity (TRIP) A1092 - 15(2020)

1.0038(dubl) - manusteelcn

Sep 17, 2013 · Samples from the standard for 50 mm (2 in) 180 ° of cold bending test:longitudinal:horizontal:Hot-rolled/Cold rolling:5 - 150:520:415:1618:2a:3.5a:Note:(1) listed in the table apex diameter (d), to steel thickness (a) multiples said. (2) in the ASTM A6 standard specified scope can meet any additional conditions. (3) from the